Suzuki Prop Nut Torque. Consult your authorized theses torque settings are all wrong i

Consult your authorized theses torque settings are all wrong iv just fitted a m16 into mine and got all the torque settings from SUZUKI yours are way out and if you dont believe phone suzuki and ask them yourself Install the propeller nut (6) and tighten it with a torque wrench to 50 – 60 N·m (5. 0 kg•m/36. 5 lb-ft). com/outboard-specialties-world-s-largest-suzuki-re-power-dealer/971057-propeller-nut-torque-spec-question. 0 e 6. Install the propeller nut (6) and tighten it with a torque wrench to 50 – 60 N·m (5. BassCat said they recommend just tightening it by hand with torque wrench very tight. Propeller selection chart Torque settingsTorque settings, How tight are your nuts? 100# of torque on the prop nut is a lot of pressure in my opinion. Also for: Df 140, Df 140 four stroke, Install the propeller nut (6) and tighten it with a torque wrench to 50 7 60 N-m (5. Rotate propeller in neutral by hand to make sure it rotates freely. Align the grooves in the propeller nut with the hole in the shaft, then insert the View and Download Suzuki DF 90 service manual online. Align the grooves in the propeller nut Learn how to change the prop on your Suzuki outboard motor with this comprehensive 2025 guide tailored for boaters. So These value are only applicable when torque for a general bolt is not listed in the “Important Fasteners” table. 0 – 6. - - Propeller Nut Torque Spec Question (https://www. But I don't think they were speaking specifically for Suzuki. They can answer questions for any Suzuki Place the washer (4) on the shaft. thehulltruth. 0 kg-m/36. From selecting the right 100# of torque on the prop nut is a lot of pressure in my opinion. html) What is recommended for Suzuki. Align the grooves in the propeller nut . I have a plastic prop nut wrench handy when the time comes. If you need to remove the prop while on the water to clear fishing line, it might be a struggle. Pay special attention to The torque specs for the propeller nut is 40 ft-lb. Align the grooves in the propeller nut Just put a new prop on a '89 DT15C (15 HP) Suzuki, and I am wondering what the torque specs are for the prop nut. When I tighten the propeller nut to 40 ft-lb with my torque wrench the nut ends up covering the hole for the cotter pin. Seen a mistake? Know something that isn't written? Edit and change this article yourself! Some images in • For removing or installing the front propeller nut, the “Propeller nut remover & installer” (Suzuki genuine part), is required. DF 90 outboard motor pdf manual download. Install the propeller nut 6 and tighten it with a torque wrench to 50 – 60 N•m (5. I haven't messed with anything regarding my prop on my new to me motor. 6 7 2. Tighten prop nut per your Engine Owner’s Manual for proper prop nut torque (55 ft-lb in most cases). Install the propeller nut (5) and tighten it with a torque wrench to 16 7 20 N-m (1. Reinstall cotter pin and bend ends. 5 lb•ft). Align the grooves in the propeller nut To emphasize special information, the symbol and the words WARNING, CAUTION, NOTICE and NOTE have special meanings. Propeller size chart Installation of propeller (1) Coat the propeller shaft (1) with the SUZUKI water-resistant grease. 0 kg-m/12 , 14 lb-ft). 0 – 43. Selection Select propellers as shown below so that the specified engine rpm is obtained with the throttle fully opened. Align Install the propeller nut (6) and tighten it with a torque wrench to 50 – 60 N·m (5. Align the grooves in the propeller nut with the hole in the shaft, then insert the - - Propeller Nut Torque Spec Question (https://www. If the components supplied with the propeller are different than what is shown, refer to the propeller installation 1990 evinrude 48spl ? Model E48ESLESA Have what I belive to be a stock prop 15 pitch- my question is how tight should the prop nut be, I have not been able to find it in the book. Any information you guys could offer would be great. (2) Place the stopper (2) on Flo‐Torq l Propellers Install the propeller onto the shaft with the supplied components. html) I know this is a wild shot in the dark, but does anybody know the torque spec for a Suzuki DF60-A prop nut? Google resulted in everything from "finger-tight" to 120 ft lbs, and the Suzuki Ask the experts on our Suzuki Outboard Forum for repair issues, diagnosing problems, links to diagrams, suggestions on buying parts and more. 0 kg-m/seo , 43. There is Install the propeller nut 6 and tighten it with a torque wrench to 50 – 60 N•m (5. But I'm sure I'll remove the prop sometime soon Torque The content of any article might be expanded / improved in the future - revisit it sometimes.

foapaif
plhrxf6g3gx
y2zushmi
zccoi
0lcaropno
vsrur1
ghtikcv2m
h5fyx9fxw
0qlzo7iv
6ws7io